X-Git-Url: http://challenge-bot.com/repos/?a=blobdiff_plain;f=3d-printables%2Fsonar-table-top-holder.scad;h=7834bc623237994e863ad6f38dbfcab29e3841c1;hb=25cd00a6b1d4f62e856346393972298f01dbabe3;hp=9cb881de5609da37309af24bcb85dd60511fba9d;hpb=fa6c6440266670ea11fda3d8bb5a9d48553e00d2;p=challenge-bot

diff --git a/3d-printables/sonar-table-top-holder.scad b/3d-printables/sonar-table-top-holder.scad
index 9cb881d..7834bc6 100644
--- a/3d-printables/sonar-table-top-holder.scad
+++ b/3d-printables/sonar-table-top-holder.scad
@@ -1,76 +1,39 @@
+/*
+  Copyright (C) 2015 Daniel Watson
+  See the end of the file for license conditions.
+*/
 // challenge-bot
 // GNU AGPLv3 (or later at your option)
-// project available at these locations:
-// https://gitorious.org/ozzloy/challenge-bot
-// https://github.com/waynegramlich/challenge-bot
+// project available here:
+// https://challenge-bot.com/
 
-$fn = 60;
+/*
+  this holds an hc-sr04 sonar sensor to a 3/16 inch deck.
+  http://fritzing.org/projects/hc-sr04-project
+  it can hold the sonar sensor either facing down, or forwards.
+  when facing down, it can detect if it passes over the edge of a table.
+  when facing forwards, it can detect and follow something in front of it.
+ */
 
-// 3/16 inch in mm deck_depth = 4.7625;
-// 1/4 inch in mm - a little to be a squeeze fit
-deck_depth = 6.35 - 0.4;
-sonar_plate_width = 20;
-// sonar sensor measurements taken with calipers:
-//  10.82 in between, 42.33 outside, 15.82 diameter
-// measured diameter of 15.82 with calipers,
-//  but when printed ends up being too small
-sonar_sensor_radius = 15.82 / 2 + 0.3;
-sonar_sensor_height = 13.8;
-between_sensor_centers = 15.82 + 10.82;
-sonar_plate_length = 3 + between_sensor_centers + sonar_sensor_radius + 3;
-sonar_holder_length = sonar_plate_length + 10;
-sonar_holder_width = sonar_plate_width + 3;
-sonar_holder_depth = 4;
+$fn = 60;
 
-deck_holder_length = 30;
-deck_holder_width = sonar_holder_width;
+include <sonar-table-top-holder-data.scad>
 
-module sensors(){
-  translate([between_sensor_centers / 2, 0, 0]){
-    cylinder(r = sonar_sensor_radius, h = sonar_sensor_height);}
-  translate([-between_sensor_centers / 2, 0, 0]){
-    cylinder(r = sonar_sensor_radius, h = sonar_sensor_height);}}
+sonar_holder();
 
-module sensor_holder(){
-  difference(){
-    cube([sonar_holder_length, sonar_holder_width, sonar_holder_depth]);
-    translate([sonar_holder_length / 2, sonar_holder_width / 2, -0.05]){
-      sensors();}}
-  translate([sonar_holder_length, 0, 0]){
-    cube([sonar_holder_depth + 0.3, deck_depth - 0.3, deck_depth - 0.3]);
-    translate([sonar_holder_depth + 0.3, 0, 0]){
-      // subtract a little bit (0.3) to make it fit
-      cube([deck_depth - 0.3, sonar_holder_width, deck_depth - 0.3]);}}}
+/*
+  This file is part of challenge-bot.
 
-module deck_holder(){
-  cube([deck_holder_length, sonar_holder_depth, sonar_holder_width]);
-  cube([sonar_holder_depth,
-        sonar_holder_depth * 2 + deck_depth,
-        sonar_holder_width]);
-  translate([0, sonar_holder_depth + deck_depth, 0]){
-    cube([deck_holder_length, sonar_holder_depth, sonar_holder_width]);}
-  translate([sonar_holder_depth + deck_depth, 0, 0]){
-    cube([sonar_holder_depth,
-          sonar_holder_depth * 2 + deck_depth,
-          sonar_holder_width]);}}
+  Challenge-bot is free software: you can redistribute it and/or modify
+  it under the terms of the GNU Affero General Public License as published by
+  the Free Software Foundation, either version 3 of the License, or
+  (at your option) any later version.
 
-module sonar_table_top_holder(){
-  difference(){
-    union(){
-      cube([sonar_holder_length, sonar_holder_width, sonar_holder_depth]);
-      translate([sonar_holder_length, 0, 0]){
-        deck_holder();}}
-    translate([between_sensor_centers / 2 + sonar_sensor_radius + 3,
-               sonar_holder_width / 2,
-               -1]){
-      sensors();}
-    // cut out a bit of the circle to make it 3d printable,
-    //  no severe overhang
-    translate([3 + sonar_sensor_radius,
-               sonar_holder_width - 3.025,
-               sonar_holder_depth / 2 - 0.025]){
-      cube([10, 6.1, sonar_holder_depth + .1], center = true);
-      translate([between_sensor_centers, 0, 0]){
-        cube([10, 6.1, sonar_holder_depth + .1], center = true);}}}}
+  GNU Affero Emacs is distributed in the hope that it will be useful,
+  but WITHOUT ANY WARRANTY; without even the implied warranty of
+  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+  GNU Affero General Public License for more details.
 
-sensor_holder();
+  You should have received a copy of the GNU Affero General Public License
+  along with challenge-bot.  If not, see <http://www.gnu.org/licenses/>.
+*/