| 47007a81 |
1 | # generated by Slic3r 1.2.10-dev on Tue Aug 11 15:59:58 2015 |
| 2 | avoid_crossing_perimeters = 0 |
| 3 | bed_shape = 0x0,140x0,140x100,0x100 |
| 4 | bed_temperature = 0 |
| 5 | before_layer_gcode = |
| 6 | bottom_solid_layers = 3 |
| 7 | bridge_acceleration = 0 |
| 8 | bridge_fan_speed = 100 |
| 9 | bridge_flow_ratio = 0.9 |
| 10 | bridge_speed = 40 |
| 11 | brim_width = 0 |
| 12 | complete_objects = 0 |
| 13 | cooling = 1 |
| 14 | default_acceleration = 0 |
| 15 | disable_fan_first_layers = 2 |
| 16 | dont_support_bridges = 1 |
| 17 | duplicate_distance = 6 |
| 18 | end_gcode = M104 S0\nM190 S0\nG1 Z100 F1000\nG1 X100 Y100 F3000\nM84 |
| 19 | external_fill_pattern = rectilinear |
| 20 | external_perimeter_extrusion_width = 0 |
| 21 | external_perimeter_speed = 30 |
| 22 | external_perimeters_first = 0 |
| 23 | extra_perimeters = 0 |
| 24 | extruder_clearance_height = 20 |
| 25 | extruder_clearance_radius = 20 |
| 26 | extruder_offset = 0x0 |
| 27 | extrusion_axis = E |
| 28 | extrusion_multiplier = 1 |
| 29 | extrusion_width = 0.35 |
| 30 | fan_always_on = 1 |
| 31 | fan_below_layer_time = 60 |
| 32 | filament_colour = #FFFFFF |
| 33 | filament_diameter = 1.75 |
| 34 | fill_angle = 45 |
| 35 | fill_density = 20% |
| 36 | fill_pattern = honeycomb |
| 37 | first_layer_acceleration = 0 |
| 38 | first_layer_bed_temperature = 0 |
| 39 | first_layer_extrusion_width = 0.4 |
| 40 | first_layer_height = 0.3 |
| 41 | first_layer_speed = 20 |
| 42 | first_layer_temperature = 230 |
| 43 | gap_fill_speed = 20 |
| 44 | gcode_arcs = 0 |
| 45 | gcode_comments = 1 |
| 46 | gcode_flavor = reprap |
| 47 | infill_acceleration = 0 |
| 48 | infill_every_layers = 1 |
| 49 | infill_extruder = 1 |
| 50 | infill_extrusion_width = 0.6 |
| 51 | infill_first = 0 |
| 52 | infill_only_where_needed = 0 |
| 53 | infill_overlap = % |
| 54 | infill_speed = 40 |
| 55 | interface_shells = 0 |
| 56 | layer_gcode = |
| 57 | layer_height = 0.1 |
| 58 | max_fan_speed = 100 |
| 59 | max_print_speed = 80 |
| 60 | max_volumetric_speed = 0 |
| 61 | min_fan_speed = 100 |
| 62 | min_print_speed = 15 |
| 63 | min_skirt_length = 25 |
| 64 | nozzle_diameter = 0.35 |
| 65 | octoprint_apikey = |
| 66 | octoprint_host = |
| 67 | only_retract_when_crossing_perimeters = 1 |
| 68 | ooze_prevention = 0 |
| 69 | output_filename_format = [input_filename_base].gcode |
| 70 | overhangs = 1 |
| 71 | perimeter_acceleration = 0 |
| 72 | perimeter_extruder = 1 |
| 73 | perimeter_extrusion_width = 0.3 |
| 74 | perimeter_speed = 35 |
| 75 | perimeters = 4 |
| 76 | post_process = |
| 77 | pressure_advance = 0 |
| 78 | raft_layers = 0 |
| 79 | resolution = 0.01 |
| 80 | retract_before_travel = 0 |
| 81 | retract_layer_change = 0 |
| 82 | retract_length = 2 |
| 83 | retract_length_toolchange = 10 |
| 84 | retract_lift = 0 |
| 85 | retract_restart_extra = 0 |
| 86 | retract_restart_extra_toolchange = 0 |
| 87 | retract_speed = 25 |
| 88 | seam_position = random |
| 89 | skirt_distance = 4 |
| 90 | skirt_height = 1 |
| 91 | skirts = 2 |
| 92 | slowdown_below_layer_time = 10 |
| 93 | small_perimeter_speed = 35 |
| 94 | solid_infill_below_area = 0 |
| 95 | solid_infill_every_layers = 0 |
| 96 | solid_infill_extruder = 1 |
| 97 | solid_infill_extrusion_width = 0.4 |
| 98 | solid_infill_speed = 40 |
| 99 | spiral_vase = 0 |
| 100 | standby_temperature_delta = -5 |
| 101 | start_gcode = G28 ;Home all axis\nT0\nM106 S0 ;EXTRUDER FAN ON\nG1 Z10 F1000\nG1 X100 Y100 F3000\nM104 S[first_layer_temperature] \nM109 S[first_layer_temperature]\nG92 E0 |
| 102 | support_material = 0 |
| 103 | support_material_angle = 45 |
| 104 | support_material_contact_distance = 0.2 |
| 105 | support_material_enforce_layers = 3 |
| 106 | support_material_extruder = 1 |
| 107 | support_material_extrusion_width = 0.25 |
| 108 | support_material_interface_extruder = 1 |
| 109 | support_material_interface_layers = 3 |
| 110 | support_material_interface_spacing = 1 |
| 111 | support_material_interface_speed = 40 |
| 112 | support_material_pattern = rectilinear-grid |
| 113 | support_material_spacing = 5 |
| 114 | support_material_speed = 40 |
| 115 | support_material_threshold = 45 |
| 116 | temperature = 215 |
| 117 | thin_walls = 1 |
| 118 | threads = 2 |
| 119 | toolchange_gcode = |
| 120 | top_infill_extrusion_width = 0.25 |
| 121 | top_solid_infill_speed = 40 |
| 122 | top_solid_layers = 4 |
| 123 | travel_speed = 100 |
| 124 | use_firmware_retraction = 0 |
| 125 | use_relative_e_distances = 0 |
| 126 | use_volumetric_e = 0 |
| 127 | vibration_limit = 0 |
| 128 | wipe = 0 |
| 129 | xy_size_compensation = 0 |
| 130 | z_offset = 0 |
projects / challenge-bot / blame