challenge-bot.com Git - challenge-bot/blob - 3d-printables/makerfarm-i3-v-8in.ini

   1 # generated by hand, probably with slic3r 1.1 or something
   2
   3 # [filament:makerfarm-i3-v-8in]
   4 bed_temperature = 70
   5 bridge_fan_speed = 100
   6 cooling = 1
   7 disable_fan_first_layers = 1
   8 extrusion_multiplier = 1
   9 fan_always_on = 1
  10 fan_below_layer_time = 60
  11 filament_diameter = 1.75
  12 first_layer_bed_temperature = 80
  13 first_layer_temperature = 235
  14 max_fan_speed = 100
  15 min_fan_speed = 35
  16 min_print_speed = 10
  17 slowdown_below_layer_time = 30
  18 temperature = 225
  19
  20 # [presets]
  21 # filament = makerfarm-i3-v-8in.ini
  22 # print = makerfarm-i3-v-8in.ini
  23 # printer = makerfarm-i3-v-8in.ini
  24
  25 # [print:makerfarm-i3-v-8in]
  26 avoid_crossing_perimeters = 1
  27 bottom_solid_layers = 3
  28 bridge_acceleration = 0
  29 bridge_flow_ratio = 1
  30 bridge_speed = 60
  31 brim_width = 0
  32 complete_objects = 0
  33 default_acceleration = 0
  34 dont_support_bridges = 1
  35 external_fill_pattern = rectilinear
  36 external_perimeter_extrusion_width = 0
  37 external_perimeter_speed = 70%
  38 external_perimeters_first = 0
  39 extra_perimeters = 1
  40 extruder_clearance_height = 20
  41 extruder_clearance_radius = 20
  42 extrusion_width = 0
  43 fill_angle = 45
  44 fill_density = 20%
  45 fill_pattern = honeycomb
  46 first_layer_acceleration = 0
  47 first_layer_extrusion_width = 200%
  48 first_layer_height = 0.35
  49 first_layer_speed = 30%
  50 gap_fill_speed = 20
  51 gcode_comments = 1
  52 infill_acceleration = 0
  53 infill_every_layers = 1
  54 infill_extruder = 1
  55 infill_extrusion_width = 0
  56 infill_first = 0
  57 infill_only_where_needed = 0
  58 infill_speed = 60
  59 interface_shells = 0
  60 layer_height = 0.2
  61 min_skirt_length = 0
  62 notes =
  63 only_retract_when_crossing_perimeters = 1
  64 ooze_prevention = 0
  65 output_filename_format = [input_filename_base].gcode
  66 overhangs = 1
  67 perimeter_acceleration = 0
  68 perimeter_extruder = 1
  69 perimeter_extrusion_width = 0
  70 perimeter_speed = 30
  71 perimeters = 3
  72 post_process =
  73 raft_layers = 0
  74 resolution = 0
  75 seam_position = aligned
  76 skirt_distance = 6
  77 skirt_height = 1
  78 skirts = 1
  79 small_perimeter_speed = 30
  80 solid_infill_below_area = 70
  81 solid_infill_every_layers = 0
  82 solid_infill_extruder = 1
  83 solid_infill_extrusion_width = 0
  84 solid_infill_speed = 60
  85 spiral_vase = 0
  86 standby_temperature_delta = -5
  87 support_material = 0
  88 support_material_angle = 0
  89 support_material_enforce_layers = 0
  90 support_material_extruder = 1
  91 support_material_extrusion_width = 0
  92 support_material_interface_extruder = 1
  93 support_material_interface_layers = 3
  94 support_material_interface_spacing = 0
  95 support_material_interface_speed = 100%
  96 support_material_pattern = pillars
  97 support_material_spacing = 2.5
  98 support_material_speed = 60
  99 support_material_threshold = 0
 100 thin_walls = 1
 101 threads = 2
 102 top_infill_extrusion_width = 0
 103 top_solid_infill_speed = 50
 104 top_solid_layers = 3
 105 travel_speed = 130
 106 xy_size_compensation = 0
 107
 108 # [printer:makerfarm-i3-v-8in]
 109 bed_shape = 0x0,200x0,200x200,0x200
 110 end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84     ; disable motors\n
 111 extruder_offset = 0x0
 112 gcode_flavor = reprap
 113 layer_gcode =
 114 nozzle_diameter = 0.4
 115 octoprint_apikey =
 116 octoprint_host =
 117 pressure_advance = 0
 118 retract_before_travel = 2
 119 retract_layer_change = 1
 120 retract_length = 1
 121 retract_length_toolchange = 10
 122 retract_lift = 0
 123 retract_restart_extra = 0
 124 retract_restart_extra_toolchange = 0
 125 retract_speed = 30
 126 start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n
 127 toolchange_gcode =
 128 use_firmware_retraction = 0
 129 use_relative_e_distances = 0
 130 use_volumetric_e = 0
 131 vibration_limit = 0
 132 wipe = 0
 133 z_offset = 0
 134
 135 # [settings]
 136 # autocenter = 1
 137 # mode = expert
 138
 139 # [simple]
 140 avoid_crossing_perimeters = 1
 141 bed_shape = 0x0,200x0,200x200,0x200
 142 bed_temperature = 70
 143 bottom_solid_layers = 3
 144 bridge_acceleration = 0
 145 bridge_fan_speed = 100
 146 bridge_flow_ratio = 1
 147 bridge_speed = 60
 148 brim_width = 0
 149 complete_objects = 0
 150 cooling = 1
 151 default_acceleration = 0
 152 disable_fan_first_layers = 1
 153 dont_support_bridges = 1
 154 duplicate_distance = 6
 155 end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84     ; disable motors\n
 156 external_fill_pattern = rectilinear
 157 external_perimeter_extrusion_width = 0
 158 external_perimeter_speed = 70%
 159 external_perimeters_first = 0
 160 extra_perimeters = 1
 161 extruder_clearance_height = 20
 162 extruder_clearance_radius = 20
 163 extruder_offset = 0x0
 164 extrusion_axis = E
 165 extrusion_multiplier = 1
 166 extrusion_width = 0
 167 fan_always_on = 0
 168 fan_below_layer_time = 60
 169 filament_diameter = 1.75
 170 fill_angle = 45
 171 fill_density = 20%
 172 fill_pattern = honeycomb
 173 first_layer_acceleration = 0
 174 first_layer_bed_temperature = 80
 175 first_layer_extrusion_width = 200%
 176 first_layer_height = 0.35
 177 first_layer_speed = 30%
 178 first_layer_temperature = 230
 179 gap_fill_speed = 20
 180 gcode_arcs = 0
 181 gcode_comments = 1
 182 gcode_flavor = reprap
 183 infill_acceleration = 0
 184 infill_every_layers = 10
 185 infill_extruder = 1
 186 infill_extrusion_width = 0
 187 infill_first = 0
 188 infill_only_where_needed = 0
 189 infill_speed = 60
 190 interface_shells = 0
 191 layer_gcode =
 192 layer_height = 0.3
 193 max_fan_speed = 100
 194 min_fan_speed = 35
 195 min_print_speed = 10
 196 min_skirt_length = 0
 197 notes =
 198 nozzle_diameter = 0.4
 199 octoprint_apikey =
 200 octoprint_host =
 201 only_retract_when_crossing_perimeters = 1
 202 ooze_prevention = 0
 203 output_filename_format = [input_filename_base].gcode
 204 overhangs = 1
 205 perimeter_acceleration = 0
 206 perimeter_extruder = 1
 207 perimeter_extrusion_width = 0
 208 perimeter_speed = 30
 209 perimeters = 3
 210 post_process =
 211 pressure_advance = 0
 212 raft_layers = 0
 213 resolution = 0
 214 retract_before_travel = 2
 215 retract_layer_change = 1
 216 retract_length = 1
 217 retract_length_toolchange = 10
 218 retract_lift = 0
 219 retract_restart_extra = 0
 220 retract_restart_extra_toolchange = 0
 221 retract_speed = 30
 222 seam_position = aligned
 223 skirt_distance = 6
 224 skirt_height = 1
 225 skirts = 1
 226 slowdown_below_layer_time = 30
 227 small_perimeter_speed = 30
 228 solid_infill_below_area = 70
 229 solid_infill_every_layers = 0
 230 solid_infill_extruder = 1
 231 solid_infill_extrusion_width = 0
 232 solid_infill_speed = 60
 233 spiral_vase = 0
 234 standby_temperature_delta = -5
 235 start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n
 236 support_material = 0
 237 support_material_angle = 0
 238 support_material_enforce_layers = 0
 239 support_material_extruder = 1
 240 support_material_extrusion_width = 0
 241 support_material_interface_extruder = 1
 242 support_material_interface_layers = 3
 243 support_material_interface_spacing = 0
 244 support_material_interface_speed = 100%
 245 support_material_pattern = pillars
 246 support_material_spacing = 2.5
 247 support_material_speed = 60
 248 support_material_threshold = 0
 249 temperature = 225
 250 thin_walls = 1
 251 threads = 2
 252 toolchange_gcode =
 253 top_infill_extrusion_width = 0
 254 top_solid_infill_speed = 50
 255 top_solid_layers = 3
 256 travel_speed = 130
 257 use_firmware_retraction = 0
 258 use_relative_e_distances = 0
 259 use_volumetric_e = 0
 260 vibration_limit = 0
 261 wipe = 0
 262 xy_size_compensation = 0
 263 z_offset = 0