make print slower and ball carrier smaller

* print slower so infill bonds and stays sturdy
* print ball holder smaller because too many balls falling out

diff --git a/3d-printables/caster-standoff-data.scad b/3d-printables/caster-standoff-data.scad
index e32b27a96181ae2670398adfa970c29d22a71cf4..828114be982255f0bd1d819281aa5c0540c8228d 100644 (file)
--- a/3d-printables/caster-standoff-data.scad
+++ b/3d-printables/caster-standoff-data.scad
@@ -13,7 +13,7 @@ use <oshw.scad>
 $fn = 60;
 
 /* measured with calipers */
-ball_diameter = 11 + 1.15; // extra bit added for printing imprecision
+ball_diameter = 11 + 1.1; // extra bit added for printing imprecision
 ball_radius = ball_diameter / 2;
 
 standoff_height = 60; // kyle eyeballed

diff --git a/3d-printables/materia-101.ini b/3d-printables/materia-101.ini
index 269296327a4f7e5245d67d25d49097976c82cad6..ecb558ef638f73a94bfec2b626edfabbadd942c0 100644 (file)
--- a/3d-printables/materia-101.ini
+++ b/3d-printables/materia-101.ini
@@ -18,14 +18,14 @@ duplicate_distance = 6
 end_gcode = M104 S0\nM190 S0\nG1 Z100 F1000\nG1 X100 Y100 F3000\nM84
 external_fill_pattern = rectilinear
 external_perimeter_extrusion_width = 0
-external_perimeter_speed = 45
+external_perimeter_speed = 11
 external_perimeters_first = 0
 extra_perimeters = 0
 extruder_clearance_height = 20
 extruder_clearance_radius = 20
 extruder_offset = 0x0
 extrusion_axis = E
-extrusion_multiplier = 1.05,1,1
+extrusion_multiplier = 1
 extrusion_width = 0
 fan_always_on = 1
 fan_below_layer_time = 60
@@ -38,9 +38,9 @@ first_layer_acceleration = 0
 first_layer_bed_temperature = 0
 first_layer_extrusion_width = 0
 first_layer_height = 0.3
-first_layer_speed = 30
+first_layer_speed = 7
 first_layer_temperature = 220
-gap_fill_speed = 40
+gap_fill_speed = 10
 gcode_arcs = 0
 gcode_comments = 1
 gcode_flavor = reprap
@@ -51,7 +51,7 @@ infill_extrusion_width = 0
 infill_first = 0
 infill_only_where_needed = 0
 infill_overlap = 100%
-infill_speed = 70
+infill_speed = 17
 interface_shells = 0
 layer_gcode =
 layer_height = 0.15
@@ -72,7 +72,7 @@ overhangs = 0
 perimeter_acceleration = 0
 perimeter_extruder = 1
 perimeter_extrusion_width = 0
-perimeter_speed = 70
+perimeter_speed = 17
 perimeters = 2
 post_process =
 pressure_advance = 0
@@ -91,12 +91,12 @@ skirt_distance = 4
 skirt_height = 1
 skirts = 4
 slowdown_below_layer_time = 5
-small_perimeter_speed = 40
+small_perimeter_speed = 10
 solid_infill_below_area = 70
 solid_infill_every_layers = 0
 solid_infill_extruder = 1
 solid_infill_extrusion_width = 0
-solid_infill_speed = 45
+solid_infill_speed = 11
 spiral_vase = 0
 standby_temperature_delta = -5
 start_gcode = G28 ;Home all axis\nT0\nM106 S0 ;EXTRUDER FAN ON\nG1 Z10 F1000\nG1 X100 Y100 F3000\nM104 S[first_layer_temperature] \nM109 S[first_layer_temperature]\nG92 E0
@@ -114,14 +114,14 @@ support_material_pattern = rectilinear-grid
 support_material_spacing = 3
 support_material_speed = 50
 support_material_threshold = 45
-temperature = 197
+temperature = 200
 thin_walls = 1
 threads = 2
 toolchange_gcode =
 top_infill_extrusion_width = 0
-top_solid_infill_speed = 40
+top_solid_infill_speed = 10
 top_solid_layers = 4
-travel_speed = 120
+travel_speed = 30
 use_firmware_retraction = 0
 use_relative_e_distances = 0
 use_volumetric_e = 0