From: daniel watson <ozzloy@gmail.com>
Date: Sat, 1 Aug 2015 20:07:03 +0000 (-0700)
Subject: modify caster to attempt to print better
X-Git-Url: http://challenge-bot.com/repos/?p=challenge-bot;a=commitdiff_plain;h=1efbaea0e88d3e76a916b0c5a60a44039267f641

modify caster to attempt to print better

* make ball smaller to grip better
* external perimeter speed up because slow speed caused bulging
* keep first layer speed slow so it adheres to print bed
* speed up gap fill speed. not sure what it does
* lower minimum print speed to accommodate slower speeds of other things
* speed up printing because slowness caused bulges
  * perimeter
  * small perimeter
  * solid infill
  * travel speed
---

diff --git a/3d-printables/caster-standoff-data.scad b/3d-printables/caster-standoff-data.scad
index 828114b..b4cf462 100644
--- a/3d-printables/caster-standoff-data.scad
+++ b/3d-printables/caster-standoff-data.scad
@@ -13,7 +13,7 @@ use <oshw.scad>
 $fn = 60;
 
 /* measured with calipers */
-ball_diameter = 11 + 1.1; // extra bit added for printing imprecision
+ball_diameter = 11 + 1; // extra bit added for printing imprecision
 ball_radius = ball_diameter / 2;
 
 standoff_height = 60; // kyle eyeballed
diff --git a/3d-printables/materia-101.ini b/3d-printables/materia-101.ini
index ecb558e..f4db62e 100644
--- a/3d-printables/materia-101.ini
+++ b/3d-printables/materia-101.ini
@@ -18,7 +18,7 @@ duplicate_distance = 6
 end_gcode = M104 S0\nM190 S0\nG1 Z100 F1000\nG1 X100 Y100 F3000\nM84
 external_fill_pattern = rectilinear
 external_perimeter_extrusion_width = 0
-external_perimeter_speed = 11
+external_perimeter_speed = 45
 external_perimeters_first = 0
 extra_perimeters = 0
 extruder_clearance_height = 20
@@ -38,9 +38,9 @@ first_layer_acceleration = 0
 first_layer_bed_temperature = 0
 first_layer_extrusion_width = 0
 first_layer_height = 0.3
-first_layer_speed = 7
+first_layer_speed = 8
 first_layer_temperature = 220
-gap_fill_speed = 10
+gap_fill_speed = 40
 gcode_arcs = 0
 gcode_comments = 1
 gcode_flavor = reprap
@@ -59,7 +59,7 @@ max_fan_speed = 100
 max_print_speed = 80
 max_volumetric_speed = 0
 min_fan_speed = 100
-min_print_speed = 20
+min_print_speed = 7
 min_skirt_length = 0
 notes = Profile for low quallity print with 20% infill and 0.15 mm z step\n\nMateria 101
 nozzle_diameter = 0.35
@@ -72,7 +72,7 @@ overhangs = 0
 perimeter_acceleration = 0
 perimeter_extruder = 1
 perimeter_extrusion_width = 0
-perimeter_speed = 17
+perimeter_speed = 70
 perimeters = 2
 post_process =
 pressure_advance = 0
@@ -91,12 +91,12 @@ skirt_distance = 4
 skirt_height = 1
 skirts = 4
 slowdown_below_layer_time = 5
-small_perimeter_speed = 10
+small_perimeter_speed = 40
 solid_infill_below_area = 70
 solid_infill_every_layers = 0
 solid_infill_extruder = 1
 solid_infill_extrusion_width = 0
-solid_infill_speed = 11
+solid_infill_speed = 45
 spiral_vase = 0
 standby_temperature_delta = -5
 start_gcode = G28 ;Home all axis\nT0\nM106 S0 ;EXTRUDER FAN ON\nG1 Z10 F1000\nG1 X100 Y100 F3000\nM104 S[first_layer_temperature] \nM109 S[first_layer_temperature]\nG92 E0
@@ -121,7 +121,7 @@ toolchange_gcode =
 top_infill_extrusion_width = 0
 top_solid_infill_speed = 10
 top_solid_layers = 4
-travel_speed = 30
+travel_speed = 120
 use_firmware_retraction = 0
 use_relative_e_distances = 0
 use_volumetric_e = 0