-// 3/16 inch in mm deck_depth = 4.7625;
-// 1/4 inch in mm = 6.35
-// subtract a little to be a squeeze fit
-deck_depth = 4.7625 - 0.4;
-sonar_plate_width = 20;
-// sonar sensor measurements taken with calipers:
-// 10.82 in between, 42.33 outside, 15.82 diameter
-// measured diameter of 15.82 with calipers,
-// but when printed ends up being too small
-sonar_sensor_radius = 15.82 / 2 + 0.3;
-sonar_sensor_height = 13.8;
-between_sensor_centers = 15.82 + 10.82;
-sonar_plate_length = 3 + between_sensor_centers + sonar_sensor_radius + 3;
-sonar_holder_length = sonar_plate_length + 10;
-sonar_holder_width = sonar_plate_width + 3;
-sonar_holder_depth = 4;
-
-deck_holder_length = 30;
-
-module sensors(){
- translate([between_sensor_centers / 2, 0, 0]){
- cylinder(r = sonar_sensor_radius, h = sonar_sensor_height);}
- translate([-between_sensor_centers / 2, 0, 0]){
- cylinder(r = sonar_sensor_radius, h = sonar_sensor_height);}}
-
-module sensor_holder(){
- difference(){
- cube([sonar_holder_length, sonar_holder_width, sonar_holder_depth]);
- translate([sonar_holder_length / 2, sonar_holder_width / 2, -0.05]){
- sensors();}}
- translate([sonar_holder_length, 0, 0]){
- cube([sonar_holder_depth + 0.7, deck_depth, deck_depth - 0.7]);
- translate([sonar_holder_depth + 0.7, 0, 0]){
- // subtract a little bit (0.3) to make it fit
- cube([deck_depth - 0.7, sonar_holder_width, deck_depth - 0.7]);}}}
-
-module deck_holder(){
- deck_holder_width = sonar_holder_width - deck_depth;
- cube([deck_holder_length, sonar_holder_depth, deck_holder_width]);
- cube([sonar_holder_depth,
- sonar_holder_depth * 2 + deck_depth,
- deck_holder_width]);
- translate([0, sonar_holder_depth + deck_depth, 0]){
- cube([deck_holder_length, sonar_holder_depth, deck_holder_width]);}
- translate([sonar_holder_depth + deck_depth, 0, 0]){
- cube([sonar_holder_depth,
- sonar_holder_depth * 2 + deck_depth,
- deck_holder_width]);}}
-
-translate([0, sonar_holder_depth * 2 + deck_depth + 2, 0]){
- sensor_holder();}
-deck_holder();
+include <sonar-table-top-holder-data.scad>
+
+sonar_holder();
+
+/*
+ This file is part of challenge-bot.
+
+ Challenge-bot is free software: you can redistribute it and/or modify
+ it under the terms of the GNU Affero General Public License as published by
+ the Free Software Foundation, either version 3 of the License, or
+ (at your option) any later version.
+
+ GNU Affero Emacs is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ GNU Affero General Public License for more details.
+
+ You should have received a copy of the GNU Affero General Public License
+ along with challenge-bot. If not, see <http://www.gnu.org/licenses/>.
+*/