[challenge-bot] / 3d-printables / makerfarm-i3-v-8in.ini

# generated by Slic3r 1.2.5 on Fri Feb 27 00:58:04 2015

[filament:makerfarmi3v8in-filament-settings]
bed_temperature = 70
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 60
filament_diameter = 1.75
first_layer_bed_temperature = 80
first_layer_temperature = 235
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 10
slowdown_below_layer_time = 30
temperature = 225

[presets]
filament = makerfarmi3v8in-filament-settings.ini
print = makerfarmi3v8in-print-settings.ini
printer = makerfarmi3v8in-printer-settings.ini

[print:Simple Mode]
bottom_solid_layers = 3
brim_width = 0
complete_objects = 0
extruder_clearance_height = 20
extruder_clearance_radius = 20
fill_density = 40%
fill_pattern = 3dhoneycomb
infill_speed = 60
layer_height = 0.3
perimeter_speed = 30
perimeters = 3
raft_layers = 0
support_material = 0
support_material_spacing = 2.5
top_solid_layers = 3
travel_speed = 130

[print:makerfarmi3v8in-print-settings]
avoid_crossing_perimeters = 1
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 60
brim_width = 0
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 70%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 20%
fill_pattern = 3dhoneycomb
first_layer_acceleration = 0
first_layer_extrusion_width = 200%
first_layer_height = 0.35
first_layer_speed = 30%
gap_fill_speed = 20
gcode_comments = 1
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 60
interface_shells = 0
layer_height = 0.2
min_skirt_length = 0
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 30
perimeters = 3
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 1
small_perimeter_speed = 30
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 60
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = pillars
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 3
travel_speed = 130
xy_size_compensation = 0

[printer:makerfarmi3v8in]
bed_shape = 0x0,200x0,200x200,0x200
end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84     ; disable motors\n
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = 
nozzle_diameter = 0.5
octoprint_apikey = 
octoprint_host = 
pressure_advance = 0
retract_before_travel = 2
retract_layer_change = 1
retract_length = 1
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 30
start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 0
z_offset = 0

[printer:makerfarmi3v8in-printer-settings]
bed_shape = 0x0,200x0,200x200,0x200
end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84     ; disable motors\n
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = 
nozzle_diameter = 0.5
octoprint_apikey = 
octoprint_host = 
pressure_advance = 0
retract_before_travel = 2
retract_layer_change = 1
retract_length = 1
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 30
start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 0
z_offset = 0

[settings]
autocenter = 1
mode = expert

[simple]
avoid_crossing_perimeters = 1
bed_shape = 0x0,200x0,200x200,0x200
bed_temperature = 70
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 60
brim_width = 0
complete_objects = 0
cooling = 1
default_acceleration = 0
disable_fan_first_layers = 1
dont_support_bridges = 1
duplicate_distance = 6
end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84     ; disable motors\n
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 70%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = 0
fan_always_on = 0
fan_below_layer_time = 60
filament_diameter = 1.75
fill_angle = 45
fill_density = 40%
fill_pattern = 3dhoneycomb
first_layer_acceleration = 0
first_layer_bed_temperature = 75
first_layer_extrusion_width = 200%
first_layer_height = 0.4
first_layer_speed = 30%
first_layer_temperature = 230
gap_fill_speed = 20
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 0
infill_every_layers = 10
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 60
interface_shells = 0
layer_gcode = 
layer_height = 0.3
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 10
min_skirt_length = 0
notes = 
nozzle_diameter = 0.4
octoprint_apikey = 
octoprint_host = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 30
perimeters = 3
post_process = 
pressure_advance = 0
raft_layers = 0
resolution = 0
retract_before_travel = 2
retract_layer_change = 1
retract_length = 1
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 30
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 1
slowdown_below_layer_time = 30
small_perimeter_speed = 30
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 60
spiral_vase = 0
standby_temperature_delta = -5
start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = pillars
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
temperature = 225
thin_walls = 1
threads = 2
toolchange_gcode = 
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 3
travel_speed = 130
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 0
xy_size_compensation = 0
z_offset = 0
Commit	Line	Data
3d90aff0	1	# generated by Slic3r 1.2.5 on Fri Feb 27 00:58:04 2015
	2
	3	[filament:makerfarmi3v8in-filament-settings]
	4	bed_temperature = 70
	5	bridge_fan_speed = 100
	6	cooling = 1
	7	disable_fan_first_layers = 1
	8	extrusion_multiplier = 1
	9	fan_always_on = 0
	10	fan_below_layer_time = 60
	11	filament_diameter = 1.75
	12	first_layer_bed_temperature = 80
	13	first_layer_temperature = 235
	14	max_fan_speed = 100
	15	min_fan_speed = 35
	16	min_print_speed = 10
	17	slowdown_below_layer_time = 30
	18	temperature = 225
	19
	20	[presets]
	21	filament = makerfarmi3v8in-filament-settings.ini
	22	print = makerfarmi3v8in-print-settings.ini
	23	printer = makerfarmi3v8in-printer-settings.ini
	24
	25	[print:Simple Mode]
	26	bottom_solid_layers = 3
	27	brim_width = 0
	28	complete_objects = 0
	29	extruder_clearance_height = 20
	30	extruder_clearance_radius = 20
	31	fill_density = 40%
	32	fill_pattern = 3dhoneycomb
	33	infill_speed = 60
	34	layer_height = 0.3
	35	perimeter_speed = 30
	36	perimeters = 3
	37	raft_layers = 0
	38	support_material = 0
	39	support_material_spacing = 2.5
	40	top_solid_layers = 3
	41	travel_speed = 130
	42
	43	[print:makerfarmi3v8in-print-settings]
	44	avoid_crossing_perimeters = 1
	45	bottom_solid_layers = 3
	46	bridge_acceleration = 0
	47	bridge_flow_ratio = 1
	48	bridge_speed = 60
	49	brim_width = 0
	50	complete_objects = 0
	51	default_acceleration = 0
	52	dont_support_bridges = 1
	53	external_fill_pattern = rectilinear
	54	external_perimeter_extrusion_width = 0
	55	external_perimeter_speed = 70%
	56	external_perimeters_first = 0
	57	extra_perimeters = 1
	58	extruder_clearance_height = 20
	59	extruder_clearance_radius = 20
	60	extrusion_width = 0
	61	fill_angle = 45
	62	fill_density = 20%
	63	fill_pattern = 3dhoneycomb
	64	first_layer_acceleration = 0
65	first_layer_extrusion_width = 200%
66	first_layer_height = 0.35
67	first_layer_speed = 30%
68	gap_fill_speed = 20
69	gcode_comments = 1
70	infill_acceleration = 0
71	infill_every_layers = 1
72	infill_extruder = 1
73	infill_extrusion_width = 0
74	infill_first = 0
75	infill_only_where_needed = 0
76	infill_speed = 60
77	interface_shells = 0
78	layer_height = 0.2
79	min_skirt_length = 0
80	notes =
81	only_retract_when_crossing_perimeters = 1
82	ooze_prevention = 0
83	output_filename_format = [input_filename_base].gcode
84	overhangs = 1
85	perimeter_acceleration = 0
86	perimeter_extruder = 1
87	perimeter_extrusion_width = 0
88	perimeter_speed = 30
89	perimeters = 3
90	post_process =
91	raft_layers = 0
92	resolution = 0
93	seam_position = aligned
94	skirt_distance = 6
95	skirt_height = 1
96	skirts = 1
97	small_perimeter_speed = 30
98	solid_infill_below_area = 70
99	solid_infill_every_layers = 0
100	solid_infill_extruder = 1
101	solid_infill_extrusion_width = 0
102	solid_infill_speed = 60
103	spiral_vase = 0
104	standby_temperature_delta = -5
105	support_material = 0
106	support_material_angle = 0
107	support_material_enforce_layers = 0
108	support_material_extruder = 1
109	support_material_extrusion_width = 0
110	support_material_interface_extruder = 1
111	support_material_interface_layers = 3
112	support_material_interface_spacing = 0
113	support_material_interface_speed = 100%
114	support_material_pattern = pillars
115	support_material_spacing = 2.5
116	support_material_speed = 60
117	support_material_threshold = 0
118	thin_walls = 1
119	threads = 2
120	top_infill_extrusion_width = 0
121	top_solid_infill_speed = 50
122	top_solid_layers = 3
123	travel_speed = 130
124	xy_size_compensation = 0
125
126	[printer:makerfarmi3v8in]
127	bed_shape = 0x0,200x0,200x200,0x200
128	end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors\n
129	extruder_offset = 0x0
130	gcode_flavor = reprap
131	layer_gcode =
132	nozzle_diameter = 0.5
133	octoprint_apikey =
134	octoprint_host =
135	pressure_advance = 0
136	retract_before_travel = 2
137	retract_layer_change = 1
138	retract_length = 1
139	retract_length_toolchange = 10
140	retract_lift = 0
141	retract_restart_extra = 0
142	retract_restart_extra_toolchange = 0
143	retract_speed = 30
144	start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n
145	toolchange_gcode =
146	use_firmware_retraction = 0
147	use_relative_e_distances = 0
148	use_volumetric_e = 0
149	vibration_limit = 0
150	wipe = 0
151	z_offset = 0
152
153	[printer:makerfarmi3v8in-printer-settings]
154	bed_shape = 0x0,200x0,200x200,0x200
155	end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors\n
156	extruder_offset = 0x0
157	gcode_flavor = reprap
158	layer_gcode =
159	nozzle_diameter = 0.5
160	octoprint_apikey =
161	octoprint_host =
162	pressure_advance = 0
163	retract_before_travel = 2
164	retract_layer_change = 1
165	retract_length = 1
166	retract_length_toolchange = 10
167	retract_lift = 0
168	retract_restart_extra = 0
169	retract_restart_extra_toolchange = 0
170	retract_speed = 30
171	start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n
172	toolchange_gcode =
173	use_firmware_retraction = 0
174	use_relative_e_distances = 0
175	use_volumetric_e = 0
176	vibration_limit = 0
177	wipe = 0
178	z_offset = 0
179
180	[settings]
181	autocenter = 1
182	mode = expert
183
184	[simple]
185	avoid_crossing_perimeters = 1
186	bed_shape = 0x0,200x0,200x200,0x200
187	bed_temperature = 70
188	bottom_solid_layers = 3
189	bridge_acceleration = 0
190	bridge_fan_speed = 100
191	bridge_flow_ratio = 1
192	bridge_speed = 60
193	brim_width = 0
194	complete_objects = 0
195	cooling = 1
196	default_acceleration = 0
197	disable_fan_first_layers = 1
198	dont_support_bridges = 1
199	duplicate_distance = 6
200	end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors\n
201	external_fill_pattern = rectilinear
202	external_perimeter_extrusion_width = 0
203	external_perimeter_speed = 70%
204	external_perimeters_first = 0
205	extra_perimeters = 1
206	extruder_clearance_height = 20
207	extruder_clearance_radius = 20
208	extruder_offset = 0x0
209	extrusion_axis = E
210	extrusion_multiplier = 1
211	extrusion_width = 0
212	fan_always_on = 0
213	fan_below_layer_time = 60
214	filament_diameter = 1.75
215	fill_angle = 45
216	fill_density = 40%
217	fill_pattern = 3dhoneycomb
218	first_layer_acceleration = 0
219	first_layer_bed_temperature = 75
220	first_layer_extrusion_width = 200%
221	first_layer_height = 0.4
222	first_layer_speed = 30%
223	first_layer_temperature = 230
224	gap_fill_speed = 20
225	gcode_arcs = 0
226	gcode_comments = 0
227	gcode_flavor = reprap
228	infill_acceleration = 0
229	infill_every_layers = 10
230	infill_extruder = 1
231	infill_extrusion_width = 0
232	infill_first = 0
233	infill_only_where_needed = 0
234	infill_speed = 60
235	interface_shells = 0
236	layer_gcode =
237	layer_height = 0.3
238	max_fan_speed = 100
239	min_fan_speed = 35
240	min_print_speed = 10
241	min_skirt_length = 0
242	notes =
243	nozzle_diameter = 0.4
244	octoprint_apikey =
245	octoprint_host =
246	only_retract_when_crossing_perimeters = 1
247	ooze_prevention = 0
248	output_filename_format = [input_filename_base].gcode
249	overhangs = 1
250	perimeter_acceleration = 0
251	perimeter_extruder = 1
252	perimeter_extrusion_width = 0
253	perimeter_speed = 30
254	perimeters = 3
255	post_process =
256	pressure_advance = 0
257	raft_layers = 0
258	resolution = 0
259	retract_before_travel = 2
260	retract_layer_change = 1
261	retract_length = 1
262	retract_length_toolchange = 10
263	retract_lift = 0
264	retract_restart_extra = 0
265	retract_restart_extra_toolchange = 0
266	retract_speed = 30
267	seam_position = aligned
268	skirt_distance = 6
269	skirt_height = 1
270	skirts = 1
271	slowdown_below_layer_time = 30
272	small_perimeter_speed = 30
273	solid_infill_below_area = 70
274	solid_infill_every_layers = 0
275	solid_infill_extruder = 1
276	solid_infill_extrusion_width = 0
277	solid_infill_speed = 60
278	spiral_vase = 0
279	standby_temperature_delta = -5
280	start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n
281	support_material = 0
282	support_material_angle = 0
283	support_material_enforce_layers = 0
284	support_material_extruder = 1
285	support_material_extrusion_width = 0
286	support_material_interface_extruder = 1
287	support_material_interface_layers = 3
288	support_material_interface_spacing = 0
289	support_material_interface_speed = 100%
290	support_material_pattern = pillars
291	support_material_spacing = 2.5
292	support_material_speed = 60
293	support_material_threshold = 0
294	temperature = 225
295	thin_walls = 1
296	threads = 2
297	toolchange_gcode =
298	top_infill_extrusion_width = 0
299	top_solid_infill_speed = 50
300	top_solid_layers = 3
301	travel_speed = 130
302	use_firmware_retraction = 0
303	use_relative_e_distances = 0
304	use_volumetric_e = 0
305	vibration_limit = 0
306	wipe = 0
307	xy_size_compensation = 0
308	z_offset = 0