update slic3r settings for 1.1.7

[challenge-bot] / 3d-printables / Makefile

diff --git a/3d-printables/Makefile b/3d-printables/Makefile
index 81a5ee922bdd1872e715e3763a96f8b0c9c17750..b7b18070adea8052a166947e3a20f8a721f6aeab 100644 (file)
--- a/3d-printables/Makefile
+++ b/3d-printables/Makefile
@@ -4,17 +4,17 @@
 %.gcode: %.stl
        slic3r \
         -o $@ \
-        -j 4 \
+        --bed-temperature 70 \
+        --first-layer-bed-temperature 80 \
+        --temperature 225 \
+        --first-layer-temperature 235 \
+        --threads 4 \
         --nozzle-diameter 0.4 \
         --print-center 95,95 \
         --z-offset 0 \
         --gcode-flavor reprap \
         --filament-diameter 1.75 \
         --extrusion-multiplier 1 \
-        --bed-temperature 70 \
-        --first-layer-bed-temperature 70 \
-        --temperature 225 \
-        --first-layer-temperature 225 \
         --travel-speed 100 \
         --perimeter-speed 75 \
         --small-perimeter-speed 50 \
@@ -35,16 +35,16 @@
         --infill-every-layers 1 \
         --solid-infill-every-layers 0 \
         --perimeters 3 \
-        --top-solid-layers 3 \
+        --top-solid-layers 4 \
         --bottom-solid-layers 3 \
-        --fill-density 0.2 \
+        --fill-density '20%' \
         --fill-angle 45 \
         --fill-pattern honeycomb \
         --solid-fill-pattern rectilinear \
         --start-gcode start.gcode \
         --end-gcode end.gcode \
         --extra-perimeters \
-        --randomize-start \
+        --seam-position nearest \
         --avoid-crossing-perimeters \
         --only-retract-when-crossing-perimeters \
         --solid-infill-below-area 70 \
@@ -96,7 +96,19 @@
         --first-layer-bed-temperature 90 \
         --temperature 215 \
         --first-layer-temperature 235 \
-        -j 4 \
+        --perimeters 3 \
+        --top-solid-layers 4 \
+        --bottom-solid-layers 3 \
+        --fill-density 20 \
+        --fill-pattern honeycomb \
+        --skirts 1 \
+        --skirt-distance 6 \
+        --skirt-height 1 \
+        --brim-width 0 \
+        --layer-height 0.2 \
+        --fill-angle 45 \
+        --min-skirt-length 0 \
+        --threads 4 \
         --nozzle-diameter 0.4 \
         --print-center 95,95 \
         --z-offset 0 \
@@ -118,21 +130,14 @@
         --infill-acceleration 0 \
         --bridge-acceleration 0 \
         --default-acceleration 0 \
-        --layer-height 0.2 \
         --first-layer-height 0.35 \
         --infill-every-layers 1 \
         --solid-infill-every-layers 0 \
-        --perimeters 3 \
-        --top-solid-layers 3 \
-        --bottom-solid-layers 3 \
-        --fill-density 0.2 \
-        --fill-angle 45 \
-        --fill-pattern honeycomb \
         --solid-fill-pattern rectilinear \
         --start-gcode start.gcode \
         --end-gcode end.gcode \
         --extra-perimeters \
-        --randomize-start \
+        --seam-position aligned \
         --avoid-crossing-perimeters \
         --only-retract-when-crossing-perimeters \
         --solid-infill-below-area 70 \
@@ -158,11 +163,6 @@
         --min-print-speed 10 \
         --disable-fan-first-layers 0 \
         --fan-always-on \
-        --skirts 1 \
-        --skirt-distance 6 \
-        --skirt-height 1 \
-        --min-skirt-length 0 \
-        --brim-width 0 \
         --bed-size 200,200 \
         --extruder-clearance-radius 20 \
         --extruder-clearance-height 20 \