define wiring in separate file

[challenge-bot] / 3d-printables / deck-holder-data.scad

diff --git a/3d-printables/deck-holder-data.scad b/3d-printables/deck-holder-data.scad
index c6a0cced65dd85d0cbf0da90807de0f0c8e6dfdf..080b5d99be9711749710116f7b68f21a19217d2f 100644 (file)
--- a/3d-printables/deck-holder-data.scad
+++ b/3d-printables/deck-holder-data.scad
@@ -1,8 +1,11 @@
+/*
+  Copyright (C) 2015 Daniel Watson
+  See the end of the file for license conditions.
+*/
 // challenge-bot
 // GNU AGPLv3 (or later at your option)
-// project available at these locations:
-// https://gitorious.org/ozzloy/challenge-bot
-// https://github.com/waynegramlich/challenge-bot
+// project available here:
+// https://challenge-bot.com/
 
 /*
   this holds an hc-sr04 sonar sensor to a 3/16 inch deck.
@@ -36,25 +39,6 @@ buffer = 3;
 sonar_holder_length = buffer + between_sonar_centers + sonar_diameter + buffer;
 sonar_holder_width = buffer + sonar_diameter + buffer;
 
-// 3/16 inch in mm deck_depth = 4.7625;
-// 1/4 inch in mm = 6.35
-// subtract a little to be a squeeze fit
-deck_depth = 4.7625 - 0.4;
-// sonar sensor measurements taken with calipers:
-//  10.82 in between, 42.33 outside, 15.82 diameter
-// measured diameter of 15.82 with calipers,
-//  but when printed ends up being too small, so add some
-sonar_diameter = 15.82 + 0.4;
-sonar_radius = sonar_diameter / 2;
-sonar_height = 13.8;
-between_sonar_centers = sonar_diameter + 10.82;
-// the sonar cylinders are placed on the pcb at slightly different positions
-//  from one sensor to the next, so this allows for that variance.
-between_sonar_centers_variance = 2;
-// keep at least this much plastic surrounding the sonar cylinder on all sides
-buffer = 3;
-sonar_holder_length = buffer + between_sonar_centers + sonar_diameter + buffer;
-sonar_holder_width = buffer + sonar_diameter + buffer;
 // sonar_holder_depth is deck_depth minus a little bit to make arm fit
 //  into deck holder
 sonar_holder_depth = deck_depth - 0.7875;
@@ -62,12 +46,30 @@ sonar_holder_depth = deck_depth - 0.7875;
 deck_holder_length = sonar_holder_depth * 2 + deck_depth + 15;
 
 module deck_holder() {
+  oshw_height = 0.75;
   deck_holder_width = sonar_holder_width - deck_depth;
   deck_holder_height = sonar_holder_depth * 2 + deck_depth;
   linear_extrude(height = deck_holder_width) {
     difference() {
       square([deck_holder_length, deck_holder_height]);
       translate([sonar_holder_depth - 0.15, sonar_holder_depth - 0.15]) {
+
+/*
+  This file is part of challenge-bot.
+
+  Challenge-bot is free software: you can redistribute it and/or modify
+  it under the terms of the GNU Affero General Public License as published by
+  the Free Software Foundation, either version 3 of the License, or
+  (at your option) any later version.
+
+  GNU Affero Emacs is distributed in the hope that it will be useful,
+  but WITHOUT ANY WARRANTY; without even the implied warranty of
+  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+  GNU Affero General Public License for more details.
+
+  You should have received a copy of the GNU Affero General Public License
+  along with challenge-bot.  If not, see <http://www.gnu.org/licenses/>.
+*/
         square(deck_depth + 0.3); }
       translate([deck_holder_height, sonar_holder_depth - 0.3]) {
         square([deck_holder_length - (deck_holder_height),