define wiring in separate file

[challenge-bot] / 3d-printables / deck.scad

diff --git a/3d-printables/deck.scad b/3d-printables/deck.scad
index 67e44c650aefd852c88edcaffebaca66fb610ff6..564d2c06f20f5e81f13d506954f79b8a7345a678 100644 (file)
--- a/3d-printables/deck.scad
+++ b/3d-printables/deck.scad
@@ -1,51 +1,34 @@
+/*
+  Copyright (C) 2015 Daniel Watson
+  See the end of the file for license conditions.
+*/
 // challenge-bot
 // GNU AGPLv3 (or later at your option)
-// project available at these locations:
-// https://gitorious.org/ozzloy/challenge-bot
-// https://github.com/waynegramlich/challenge-bot
+// project available here:
+// https://challenge-bot.com/
 
-// all measurements are in mm unless stated otherwise
-
-  // metric version of deck:
-deck_length = 200;
-deck_width = deck_length;
-deck_depth = 5;
-deck_pitch = 10;
-deck_grid_hole = 3;
-deck_hole_type = "square";
-
-  /*
-    // imperial version of deck
-deck_length = 203.2; // 8 inches
-deck_width = deck_length;
-deck_depth = 25.4 * 3 / 16; // 3 / 16 of an inch
-deck_pitch = 25.4; // 1 inch
-deck_grid_hole = 6.35 / 2; // 1/4 inch diameter, 1/8 inch radius
-deck_hole_type = "circle";
-  */
-
-module deck_2d(width, length, pitch, hole, hole_type, center=false){
-  center_width_offset = center ? -(width / 2): 0;
-  center_length_offset = center ? -(length / 2): 0;
-  translate([center_width_offset, center_length_offset]){
-    difference(){
-      square([width, length]);
-      for (y = [0:floor(length / pitch) - 1],
-           x = [0:floor(width / pitch) - 1]){
-        translate([pitch * (x + 0.5), pitch * (y + 0.5)]){
-          if (hole_type == "circle"){
-            circle(hole, center = true);}
-          else if (hole_type == "square") {
-            square(hole, center = true);}
-          else {
-            echo(str("don't know the hole type: ", hole_type));}}}}}}
-
-module deck(width, length, depth, pitch, hole, hole_type, center=false){
-  linear_extrude (height = depth){
-    deck_2d(width, length, pitch, hole, hole_type, center);}}
+include <deck-data.scad>
 
 deck_2d(deck_width,
         deck_length,
         deck_pitch,
         deck_grid_hole,
-        deck_hole_type);
+        deck_hole_type,
+        center = deck_centered);
+
+/*
+  This file is part of challenge-bot.
+
+  Challenge-bot is free software: you can redistribute it and/or modify
+  it under the terms of the GNU Affero General Public License as published by
+  the Free Software Foundation, either version 3 of the License, or
+  (at your option) any later version.
+
+  GNU Affero Emacs is distributed in the hope that it will be useful,
+  but WITHOUT ANY WARRANTY; without even the implied warranty of
+  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+  GNU Affero General Public License for more details.
+
+  You should have received a copy of the GNU Affero General Public License
+  along with challenge-bot.  If not, see <http://www.gnu.org/licenses/>.
+*/