add extension with hole for screw

[challenge-bot] / 3d-printables / sonar-binder-clip-holder-data.scad

/*
  Copyright 2016 Daniel Watson
  See the end of the file for license conditions.
*/
/* challenge-bot
// GNU AGPLv3 (or later at your option)
// project available here:
// https://challenge-bot.com/ */

/*
  this holds an hc-sr04 sonar sensor to a 3/16 inch deck.
  http://fritzing.org/projects/hc-sr04-project
  it can hold the sonar sensor either facing down, or forwards.
  when facing down, it can detect if it passes over the edge of a table.
  when facing forwards, it can detect and follow something in front
  of it.
*/

$fn = 50;

sonar_diameter_measured = 15.82;
sonar_diameter_print_fudge = 0.5;
sonar_diameter = sonar_diameter_measured + sonar_diameter_print_fudge;
sonar_radius = sonar_diameter / 2;

between_sonar_cans = 10.82;
between_sonar_centers = sonar_diameter + between_sonar_cans;

// the sonar cylinders are placed on the pcb at slightly different positions
//  from one sensor to the next, so this allows for that variance.
between_sonar_centers_variation = 2;

wall_thickness = 3;

screw_radius_measured = 2.8;
screw_radius_print_fudge = 0.3;
screw_radius = screw_radius_measured + screw_radius_print_fudge;

module sonar_sensors_2d(sonar_radius,
                        between_sonar_centers,
                        between_sonar_centers_variation) {
  hull(){
    circle(sonar_radius);
    translate([between_sonar_centers_variation, 0]){
      circle(sonar_radius); } }
  translate([between_sonar_centers, 0]) {
    circle(sonar_radius); } }

module sonar_holder_outline_2d(sonar_radius,
                               between_sonar_centers,
                               wall_thickness) {
  holder_radius = sonar_radius + wall_thickness;
  holder_diameter = holder_radius * 2;
  hull() {
    circle(holder_radius);
    translate([between_sonar_centers, 0]) {
      circle(holder_radius); }
    translate([sonar_radius + between_sonar_centers, -holder_radius]) {
      square([holder_diameter * 2, holder_diameter]); } } }

module sonar_binder_clip_holder(sonar_radius,
                                between_sonar_centers,
                                between_sonar_centers_variation,
                                wall_thickness) {
  difference() {
    sonar_holder_outline_2d(sonar_radius,
                            between_sonar_centers,
                            wall_thickness);
    sonar_sensors_2d(sonar_radius,
                     between_sonar_centers,
                     between_sonar_centers_variation);
    translate([sonar_radius +
               between_sonar_centers +
               3 * (wall_thickness + sonar_radius),
               0,
               0]) {
      circle(screw_radius); } } }

/*
  This file is part of challenge-bot.

  Challenge-bot is free software: you can redistribute it and/or modify
  it under the terms of the GNU Affero General Public License as published by
  the Free Software Foundation, either version 3 of the License, or
  (at your option) any later version.

  GNU Affero Emacs is distributed in the hope that it will be useful,
  but WITHOUT ANY WARRANTY; without even the implied warranty of
  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  GNU Affero General Public License for more details.

  You should have received a copy of the GNU Affero General Public License
  along with challenge-bot.  If not, see <http://www.gnu.org/licenses/>.
*/