challenge-bot.com Git - challenge-bot/blob - 3d-printables/makerfarm-i3-v-8in.ini

   1 # generated by Slic3r 1.2.5 on Fri Feb 27 00:58:04 2015
   2
   3 [filament:makerfarmi3v8in-filament-settings]
   4 bed_temperature = 70
   5 bridge_fan_speed = 100
   6 cooling = 1
   7 disable_fan_first_layers = 1
   8 extrusion_multiplier = 1
   9 fan_always_on = 0
  10 fan_below_layer_time = 60
  11 filament_diameter = 1.75
  12 first_layer_bed_temperature = 80
  13 first_layer_temperature = 235
  14 max_fan_speed = 100
  15 min_fan_speed = 35
  16 min_print_speed = 10
  17 slowdown_below_layer_time = 30
  18 temperature = 225
  19
  20 [presets]
  21 filament = makerfarmi3v8in-filament-settings.ini
  22 print = makerfarmi3v8in-print-settings.ini
  23 printer = makerfarmi3v8in-printer-settings.ini
  24
  25 [print:Simple Mode]
  26 bottom_solid_layers = 3
  27 brim_width = 0
  28 complete_objects = 0
  29 extruder_clearance_height = 20
  30 extruder_clearance_radius = 20
  31 fill_density = 40%
  32 fill_pattern = 3dhoneycomb
  33 infill_speed = 60
  34 layer_height = 0.3
  35 perimeter_speed = 30
  36 perimeters = 3
  37 raft_layers = 0
  38 support_material = 0
  39 support_material_spacing = 2.5
  40 top_solid_layers = 3
  41 travel_speed = 130
  42
  43 [print:makerfarmi3v8in-print-settings]
  44 avoid_crossing_perimeters = 1
  45 bottom_solid_layers = 3
  46 bridge_acceleration = 0
  47 bridge_flow_ratio = 1
  48 bridge_speed = 60
  49 brim_width = 0
  50 complete_objects = 0
  51 default_acceleration = 0
  52 dont_support_bridges = 1
  53 external_fill_pattern = rectilinear
  54 external_perimeter_extrusion_width = 0
  55 external_perimeter_speed = 70%
  56 external_perimeters_first = 0
  57 extra_perimeters = 1
  58 extruder_clearance_height = 20
  59 extruder_clearance_radius = 20
  60 extrusion_width = 0
  61 fill_angle = 45
  62 fill_density = 20%
  63 fill_pattern = 3dhoneycomb
  64 first_layer_acceleration = 0
  65 first_layer_extrusion_width = 200%
  66 first_layer_height = 0.35
  67 first_layer_speed = 30%
  68 gap_fill_speed = 20
  69 gcode_comments = 1
  70 infill_acceleration = 0
  71 infill_every_layers = 1
  72 infill_extruder = 1
  73 infill_extrusion_width = 0
  74 infill_first = 0
  75 infill_only_where_needed = 0
  76 infill_speed = 60
  77 interface_shells = 0
  78 layer_height = 0.2
  79 min_skirt_length = 0
  80 notes =
  81 only_retract_when_crossing_perimeters = 1
  82 ooze_prevention = 0
  83 output_filename_format = [input_filename_base].gcode
  84 overhangs = 1
  85 perimeter_acceleration = 0
  86 perimeter_extruder = 1
  87 perimeter_extrusion_width = 0
  88 perimeter_speed = 30
  89 perimeters = 3
  90 post_process =
  91 raft_layers = 0
  92 resolution = 0
  93 seam_position = aligned
  94 skirt_distance = 6
  95 skirt_height = 1
  96 skirts = 1
  97 small_perimeter_speed = 30
  98 solid_infill_below_area = 70
  99 solid_infill_every_layers = 0
 100 solid_infill_extruder = 1
 101 solid_infill_extrusion_width = 0
 102 solid_infill_speed = 60
 103 spiral_vase = 0
 104 standby_temperature_delta = -5
 105 support_material = 0
 106 support_material_angle = 0
 107 support_material_enforce_layers = 0
 108 support_material_extruder = 1
 109 support_material_extrusion_width = 0
 110 support_material_interface_extruder = 1
 111 support_material_interface_layers = 3
 112 support_material_interface_spacing = 0
 113 support_material_interface_speed = 100%
 114 support_material_pattern = pillars
 115 support_material_spacing = 2.5
 116 support_material_speed = 60
 117 support_material_threshold = 0
 118 thin_walls = 1
 119 threads = 2
 120 top_infill_extrusion_width = 0
 121 top_solid_infill_speed = 50
 122 top_solid_layers = 3
 123 travel_speed = 130
 124 xy_size_compensation = 0
 125
 126 [printer:makerfarmi3v8in]
 127 bed_shape = 0x0,200x0,200x200,0x200
 128 end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84     ; disable motors\n
 129 extruder_offset = 0x0
 130 gcode_flavor = reprap
 131 layer_gcode =
 132 nozzle_diameter = 0.5
 133 octoprint_apikey =
 134 octoprint_host =
 135 pressure_advance = 0
 136 retract_before_travel = 2
 137 retract_layer_change = 1
 138 retract_length = 1
 139 retract_length_toolchange = 10
 140 retract_lift = 0
 141 retract_restart_extra = 0
 142 retract_restart_extra_toolchange = 0
 143 retract_speed = 30
 144 start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n
 145 toolchange_gcode =
 146 use_firmware_retraction = 0
 147 use_relative_e_distances = 0
 148 use_volumetric_e = 0
 149 vibration_limit = 0
 150 wipe = 0
 151 z_offset = 0
 152
 153 [printer:makerfarmi3v8in-printer-settings]
 154 bed_shape = 0x0,200x0,200x200,0x200
 155 end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84     ; disable motors\n
 156 extruder_offset = 0x0
 157 gcode_flavor = reprap
 158 layer_gcode =
 159 nozzle_diameter = 0.5
 160 octoprint_apikey =
 161 octoprint_host =
 162 pressure_advance = 0
 163 retract_before_travel = 2
 164 retract_layer_change = 1
 165 retract_length = 1
 166 retract_length_toolchange = 10
 167 retract_lift = 0
 168 retract_restart_extra = 0
 169 retract_restart_extra_toolchange = 0
 170 retract_speed = 30
 171 start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n
 172 toolchange_gcode =
 173 use_firmware_retraction = 0
 174 use_relative_e_distances = 0
 175 use_volumetric_e = 0
 176 vibration_limit = 0
 177 wipe = 0
 178 z_offset = 0
 179
 180 [settings]
 181 autocenter = 1
 182 mode = expert
 183
 184 [simple]
 185 avoid_crossing_perimeters = 1
 186 bed_shape = 0x0,200x0,200x200,0x200
 187 bed_temperature = 70
 188 bottom_solid_layers = 3
 189 bridge_acceleration = 0
 190 bridge_fan_speed = 100
 191 bridge_flow_ratio = 1
 192 bridge_speed = 60
 193 brim_width = 0
 194 complete_objects = 0
 195 cooling = 1
 196 default_acceleration = 0
 197 disable_fan_first_layers = 1
 198 dont_support_bridges = 1
 199 duplicate_distance = 6
 200 end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84     ; disable motors\n
 201 external_fill_pattern = rectilinear
 202 external_perimeter_extrusion_width = 0
 203 external_perimeter_speed = 70%
 204 external_perimeters_first = 0
 205 extra_perimeters = 1
 206 extruder_clearance_height = 20
 207 extruder_clearance_radius = 20
 208 extruder_offset = 0x0
 209 extrusion_axis = E
 210 extrusion_multiplier = 1
 211 extrusion_width = 0
 212 fan_always_on = 0
 213 fan_below_layer_time = 60
 214 filament_diameter = 1.75
 215 fill_angle = 45
 216 fill_density = 40%
 217 fill_pattern = 3dhoneycomb
 218 first_layer_acceleration = 0
 219 first_layer_bed_temperature = 75
 220 first_layer_extrusion_width = 200%
 221 first_layer_height = 0.4
 222 first_layer_speed = 30%
 223 first_layer_temperature = 230
 224 gap_fill_speed = 20
 225 gcode_arcs = 0
 226 gcode_comments = 0
 227 gcode_flavor = reprap
 228 infill_acceleration = 0
 229 infill_every_layers = 10
 230 infill_extruder = 1
 231 infill_extrusion_width = 0
 232 infill_first = 0
 233 infill_only_where_needed = 0
 234 infill_speed = 60
 235 interface_shells = 0
 236 layer_gcode =
 237 layer_height = 0.3
 238 max_fan_speed = 100
 239 min_fan_speed = 35
 240 min_print_speed = 10
 241 min_skirt_length = 0
 242 notes =
 243 nozzle_diameter = 0.4
 244 octoprint_apikey =
 245 octoprint_host =
 246 only_retract_when_crossing_perimeters = 1
 247 ooze_prevention = 0
 248 output_filename_format = [input_filename_base].gcode
 249 overhangs = 1
 250 perimeter_acceleration = 0
 251 perimeter_extruder = 1
 252 perimeter_extrusion_width = 0
 253 perimeter_speed = 30
 254 perimeters = 3
 255 post_process =
 256 pressure_advance = 0
 257 raft_layers = 0
 258 resolution = 0
 259 retract_before_travel = 2
 260 retract_layer_change = 1
 261 retract_length = 1
 262 retract_length_toolchange = 10
 263 retract_lift = 0
 264 retract_restart_extra = 0
 265 retract_restart_extra_toolchange = 0
 266 retract_speed = 30
 267 seam_position = aligned
 268 skirt_distance = 6
 269 skirt_height = 1
 270 skirts = 1
 271 slowdown_below_layer_time = 30
 272 small_perimeter_speed = 30
 273 solid_infill_below_area = 70
 274 solid_infill_every_layers = 0
 275 solid_infill_extruder = 1
 276 solid_infill_extrusion_width = 0
 277 solid_infill_speed = 60
 278 spiral_vase = 0
 279 standby_temperature_delta = -5
 280 start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n
 281 support_material = 0
 282 support_material_angle = 0
 283 support_material_enforce_layers = 0
 284 support_material_extruder = 1
 285 support_material_extrusion_width = 0
 286 support_material_interface_extruder = 1
 287 support_material_interface_layers = 3
 288 support_material_interface_spacing = 0
 289 support_material_interface_speed = 100%
 290 support_material_pattern = pillars
 291 support_material_spacing = 2.5
 292 support_material_speed = 60
 293 support_material_threshold = 0
 294 temperature = 225
 295 thin_walls = 1
 296 threads = 2
 297 toolchange_gcode =
 298 top_infill_extrusion_width = 0
 299 top_solid_infill_speed = 50
 300 top_solid_layers = 3
 301 travel_speed = 130
 302 use_firmware_retraction = 0
 303 use_relative_e_distances = 0
 304 use_volumetric_e = 0
 305 vibration_limit = 0
 306 wipe = 0
 307 xy_size_compensation = 0
 308 z_offset = 0