2 ;; copyright info at bottom
9 :title [arduino to deck]
13 :title [choosing drill bit]
17 [what would happen if the drill bit were larger than the
20 [what would happen if the drill bit were smaller than the
23 :title [inserting drill bit]
27 [where should the teeth clamp down on the drill bit?])
29 [what would happen if the teeth tightened on the recessed
30 part of the drill bit?])))
32 :title [arduino placement]
36 [should the arduino be upside-down?])
38 [what should the upper side of the arduino align with?])
40 [why not place the arduino up along the left side of the
43 :title [drilling practice]
47 [should the drill be at full speed while the drill bit is
48 going down into the wood and coming back up?])
50 [how do you keep the drill at full speed?])
52 [what would happen if the drill bit were not at full
55 [what would happen if the drill were twisted sideways while
56 the drill bit were in the wood?]))))
60 :title [fastening arduino to deck using #6-32x3/8\" screw]
64 [in the motor assembly, there are #4-40x1.25\" screws.
65 are those fatter, thinner, or the same thickness as the
66 #6-32x3/8\" screws?]))
69 (item [how many times will the thread wrap around one inch of
71 (item [what about 2 inches?
72 how many times will the thread wrap around two
73 inches of the screw body?])
74 (item [what part of the screw does the screw driver go into?])))
76 :title [fasten the arduino board to the deck]
79 (item [why do we insert the first screw partially before
80 holding up the arduino?])
81 (item [which side of the deck is the top side?])))))
86 (item [should the black chip be on the right or the left?])
87 (item [how many glue dots should be on the breadboard?])))
89 :title [battery packs]
96 (item [should you pick up a battery by its leads?])
97 (item [should you strip the leads a large amount at a time?])
98 (item [what's the name of wires made of a bunch of tiny
104 (item [why are we using a solid core wire?])))
109 (item [should the wires melt the solder?])
110 (item [why should we clean off the tip of the soldering iron?])
111 (item [why do we put more solder back on the tip of the iron?]))))
113 :title [deck attachment]
115 :title [motor battery pack attachment]
118 (item [why place the glue dots on the side of the battery pack
119 without the on/off switch?])))
121 :title [arduino battery pack attachment]
124 (item [why align the screw with a hole on the deck?])))))
131 (item [should the electrical tape go between the wires and the
133 (item [are the motor tabs strong?])
134 (item [what are we doing to reinforce the motor tabs mechanically?])
135 (item [does hot glue make an electrical connection?])))
139 :title [angle bracket to motor mount]
142 (item [should the motor mounts have angle brackets attached in
143 a mirror image fashion?])
144 (item [why should the motor mounts have angle brackets attached in
145 a mirror image fashion?])))
147 :title [motor mount to motor]
150 (item [is the #4 bolt thicker or thinner than the #6?])
151 (item [do you have a ratcheting socket wrench, or not?]))))
153 :title [deck attachment]))
158 (item [what would happen if the robot did not have a caster?])))
163 (item [does the robot's wheels scrape the deck?])
164 (item [what would happen if the robot had no wheels?])
165 (item [what does the tread do?])
166 (item [what is the tread?])
167 (item [what kind of screw is used?])))
172 (item [are your sonar sensors pointy pins facing in toward the
174 (item [was it difficult to get the sonar into the holder?])
175 (item [what would happen if it was easy to slip the sonar sensor
176 into the sonar holder?])))))
178 ;; Copyright 2016 daniel watson
180 ;; This file is part of challenge-bot.
182 ;; challenge-bot is free software: you can redistribute it and/or modify
183 ;; it under the terms of the GNU Affero General Public License as
184 ;; published by the Free Software Foundation, either version 3 of the
185 ;; License, or (at your option) any later version.
187 ;; challenge-bot is distributed in the hope that it will be useful,
188 ;; but WITHOUT ANY WARRANTY; without even the implied warranty of
189 ;; MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
190 ;; GNU Affero General Public License for more details.
192 ;; You should have received a copy of the GNU Affero General Public
193 ;; License along with challenge-bot. If not, see
194 ;; <http://www.gnu.org/licenses/>.