[challenge-bot] / 3d-printables / makerfarm-i3-v-8in.ini


# [filament:makerfarm-i3-v-8in]
bed_temperature = 70
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 60
filament_diameter = 1.75
first_layer_bed_temperature = 80
first_layer_temperature = 235
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 10
slowdown_below_layer_time = 30
temperature = 225

# [presets]
# filament = makerfarm-i3-v-8in.ini
# print = makerfarm-i3-v-8in.ini
# printer = makerfarm-i3-v-8in.ini

# [print:makerfarm-i3-v-8in]
avoid_crossing_perimeters = 1
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 60
brim_width = 0
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 70%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 20%
fill_pattern = 3dhoneycomb
first_layer_acceleration = 0
first_layer_extrusion_width = 200%
first_layer_height = 0.35
first_layer_speed = 30%
gap_fill_speed = 20
gcode_comments = 1
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 60
interface_shells = 0
layer_height = 0.2
min_skirt_length = 0
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 30
perimeters = 3
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 1
small_perimeter_speed = 30
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 60
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = pillars
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 3
travel_speed = 130
xy_size_compensation = 0

# [printer:makerfarm-i3-v-8in]
bed_shape = 0x0,200x0,200x200,0x200
end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84     ; disable motors\n
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = 
nozzle_diameter = 0.4
octoprint_apikey = 
octoprint_host = 
pressure_advance = 0
retract_before_travel = 2
retract_layer_change = 1
retract_length = 1
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 30
start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 0
z_offset = 0

# [settings]
# autocenter = 1
# mode = expert

# [simple]
avoid_crossing_perimeters = 1
bed_shape = 0x0,200x0,200x200,0x200
bed_temperature = 70
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 60
brim_width = 0
complete_objects = 0
cooling = 1
default_acceleration = 0
disable_fan_first_layers = 1
dont_support_bridges = 1
duplicate_distance = 6
end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84     ; disable motors\n
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 70%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = 0
fan_always_on = 0
fan_below_layer_time = 60
filament_diameter = 1.75
fill_angle = 45
fill_density = 20%
fill_pattern = 3dhoneycomb
first_layer_acceleration = 0
first_layer_bed_temperature = 80
first_layer_extrusion_width = 200%
first_layer_height = 0.35
first_layer_speed = 30%
first_layer_temperature = 230
gap_fill_speed = 20
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 0
infill_every_layers = 10
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 60
interface_shells = 0
layer_gcode = 
layer_height = 0.3
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 10
min_skirt_length = 0
notes = 
nozzle_diameter = 0.4
octoprint_apikey = 
octoprint_host = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 30
perimeters = 3
post_process = 
pressure_advance = 0
raft_layers = 0
resolution = 0
retract_before_travel = 2
retract_layer_change = 1
retract_length = 1
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 30
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 1
slowdown_below_layer_time = 30
small_perimeter_speed = 30
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 60
spiral_vase = 0
standby_temperature_delta = -5
start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = pillars
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
temperature = 225
thin_walls = 1
threads = 2
toolchange_gcode = 
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 3
travel_speed = 130
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 0
xy_size_compensation = 0
z_offset = 0
Commit	Line	Data
3d90aff0	1
eaa6ba7e	2	# [filament:makerfarm-i3-v-8in]
3d90aff0	3	bed_temperature = 70
	4	bridge_fan_speed = 100
	5	cooling = 1
	6	disable_fan_first_layers = 1
	7	extrusion_multiplier = 1
eaa6ba7e	8	fan_always_on = 1
3d90aff0	9	fan_below_layer_time = 60
	10	filament_diameter = 1.75
	11	first_layer_bed_temperature = 80
	12	first_layer_temperature = 235
	13	max_fan_speed = 100
	14	min_fan_speed = 35
	15	min_print_speed = 10
	16	slowdown_below_layer_time = 30
	17	temperature = 225
	18
eaa6ba7e	19	# [presets]
	20	# filament = makerfarm-i3-v-8in.ini
	21	# print = makerfarm-i3-v-8in.ini
	22	# printer = makerfarm-i3-v-8in.ini
3d90aff0	23
eaa6ba7e	24	# [print:makerfarm-i3-v-8in]
3d90aff0	25	avoid_crossing_perimeters = 1
	26	bottom_solid_layers = 3
	27	bridge_acceleration = 0
	28	bridge_flow_ratio = 1
	29	bridge_speed = 60
	30	brim_width = 0
	31	complete_objects = 0
	32	default_acceleration = 0
	33	dont_support_bridges = 1
	34	external_fill_pattern = rectilinear
	35	external_perimeter_extrusion_width = 0
	36	external_perimeter_speed = 70%
	37	external_perimeters_first = 0
	38	extra_perimeters = 1
	39	extruder_clearance_height = 20
	40	extruder_clearance_radius = 20
	41	extrusion_width = 0
	42	fill_angle = 45
	43	fill_density = 20%
	44	fill_pattern = 3dhoneycomb
	45	first_layer_acceleration = 0
	46	first_layer_extrusion_width = 200%
	47	first_layer_height = 0.35
	48	first_layer_speed = 30%
	49	gap_fill_speed = 20
	50	gcode_comments = 1
	51	infill_acceleration = 0
	52	infill_every_layers = 1
	53	infill_extruder = 1
	54	infill_extrusion_width = 0
	55	infill_first = 0
	56	infill_only_where_needed = 0
	57	infill_speed = 60
	58	interface_shells = 0
	59	layer_height = 0.2
	60	min_skirt_length = 0
	61	notes =
	62	only_retract_when_crossing_perimeters = 1
	63	ooze_prevention = 0
	64	output_filename_format = [input_filename_base].gcode
	65	overhangs = 1
	66	perimeter_acceleration = 0
	67	perimeter_extruder = 1
	68	perimeter_extrusion_width = 0
	69	perimeter_speed = 30
	70	perimeters = 3
	71	post_process =
	72	raft_layers = 0
	73	resolution = 0
	74	seam_position = aligned
	75	skirt_distance = 6
	76	skirt_height = 1
	77	skirts = 1
	78	small_perimeter_speed = 30
	79	solid_infill_below_area = 70
	80	solid_infill_every_layers = 0
	81	solid_infill_extruder = 1
	82	solid_infill_extrusion_width = 0
	83	solid_infill_speed = 60
	84	spiral_vase = 0
	85	standby_temperature_delta = -5
	86	support_material = 0
	87	support_material_angle = 0
	88	support_material_enforce_layers = 0
89	support_material_extruder = 1
90	support_material_extrusion_width = 0
91	support_material_interface_extruder = 1
92	support_material_interface_layers = 3
93	support_material_interface_spacing = 0
94	support_material_interface_speed = 100%
95	support_material_pattern = pillars
96	support_material_spacing = 2.5
97	support_material_speed = 60
98	support_material_threshold = 0
99	thin_walls = 1
100	threads = 2
101	top_infill_extrusion_width = 0
102	top_solid_infill_speed = 50
103	top_solid_layers = 3
104	travel_speed = 130
105	xy_size_compensation = 0
106
eaa6ba7e	107	# [printer:makerfarm-i3-v-8in]
3d90aff0	108	bed_shape = 0x0,200x0,200x200,0x200
	109	end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors\n
	110	extruder_offset = 0x0
	111	gcode_flavor = reprap
	112	layer_gcode =
eaa6ba7e	113	nozzle_diameter = 0.4
3d90aff0	114	octoprint_apikey =
	115	octoprint_host =
	116	pressure_advance = 0
	117	retract_before_travel = 2
	118	retract_layer_change = 1
	119	retract_length = 1
	120	retract_length_toolchange = 10
	121	retract_lift = 0
	122	retract_restart_extra = 0
	123	retract_restart_extra_toolchange = 0
	124	retract_speed = 30
	125	start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n
	126	toolchange_gcode =
	127	use_firmware_retraction = 0
	128	use_relative_e_distances = 0
	129	use_volumetric_e = 0
	130	vibration_limit = 0
	131	wipe = 0
	132	z_offset = 0
	133
eaa6ba7e	134	# [settings]
	135	# autocenter = 1
	136	# mode = expert
3d90aff0	137
eaa6ba7e	138	# [simple]
3d90aff0	139	avoid_crossing_perimeters = 1
	140	bed_shape = 0x0,200x0,200x200,0x200
	141	bed_temperature = 70
	142	bottom_solid_layers = 3
	143	bridge_acceleration = 0
	144	bridge_fan_speed = 100
	145	bridge_flow_ratio = 1
	146	bridge_speed = 60
	147	brim_width = 0
	148	complete_objects = 0
	149	cooling = 1
	150	default_acceleration = 0
	151	disable_fan_first_layers = 1
	152	dont_support_bridges = 1
	153	duplicate_distance = 6
	154	end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors\n
	155	external_fill_pattern = rectilinear
	156	external_perimeter_extrusion_width = 0
	157	external_perimeter_speed = 70%
	158	external_perimeters_first = 0
	159	extra_perimeters = 1
	160	extruder_clearance_height = 20
	161	extruder_clearance_radius = 20
	162	extruder_offset = 0x0
	163	extrusion_axis = E
	164	extrusion_multiplier = 1
	165	extrusion_width = 0
	166	fan_always_on = 0
	167	fan_below_layer_time = 60
	168	filament_diameter = 1.75
	169	fill_angle = 45
eaa6ba7e	170	fill_density = 20%
3d90aff0	171	fill_pattern = 3dhoneycomb
3d90aff0	172	first_layer_acceleration = 0
eaa6ba7e	173	first_layer_bed_temperature = 80
3d90aff0	174	first_layer_extrusion_width = 200%
eaa6ba7e	175	first_layer_height = 0.35
3d90aff0	176	first_layer_speed = 30%
	177	first_layer_temperature = 230
	178	gap_fill_speed = 20
	179	gcode_arcs = 0
	180	gcode_comments = 0
	181	gcode_flavor = reprap
	182	infill_acceleration = 0
	183	infill_every_layers = 10
	184	infill_extruder = 1
	185	infill_extrusion_width = 0
	186	infill_first = 0
	187	infill_only_where_needed = 0
	188	infill_speed = 60
	189	interface_shells = 0
	190	layer_gcode =
	191	layer_height = 0.3
	192	max_fan_speed = 100
	193	min_fan_speed = 35
	194	min_print_speed = 10
	195	min_skirt_length = 0
	196	notes =
	197	nozzle_diameter = 0.4
	198	octoprint_apikey =
	199	octoprint_host =
	200	only_retract_when_crossing_perimeters = 1
	201	ooze_prevention = 0
	202	output_filename_format = [input_filename_base].gcode
	203	overhangs = 1
	204	perimeter_acceleration = 0
	205	perimeter_extruder = 1
	206	perimeter_extrusion_width = 0
	207	perimeter_speed = 30
	208	perimeters = 3
	209	post_process =
	210	pressure_advance = 0
	211	raft_layers = 0
	212	resolution = 0
	213	retract_before_travel = 2
	214	retract_layer_change = 1
	215	retract_length = 1
	216	retract_length_toolchange = 10
	217	retract_lift = 0
	218	retract_restart_extra = 0
	219	retract_restart_extra_toolchange = 0
	220	retract_speed = 30
	221	seam_position = aligned
	222	skirt_distance = 6
	223	skirt_height = 1
	224	skirts = 1
	225	slowdown_below_layer_time = 30
	226	small_perimeter_speed = 30
	227	solid_infill_below_area = 70
	228	solid_infill_every_layers = 0
	229	solid_infill_extruder = 1
	230	solid_infill_extrusion_width = 0
	231	solid_infill_speed = 60
	232	spiral_vase = 0
	233	standby_temperature_delta = -5
	234	start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n
	235	support_material = 0
	236	support_material_angle = 0
	237	support_material_enforce_layers = 0
	238	support_material_extruder = 1
	239	support_material_extrusion_width = 0
240	support_material_interface_extruder = 1
241	support_material_interface_layers = 3
242	support_material_interface_spacing = 0
243	support_material_interface_speed = 100%
244	support_material_pattern = pillars
245	support_material_spacing = 2.5
246	support_material_speed = 60
247	support_material_threshold = 0
248	temperature = 225
249	thin_walls = 1
250	threads = 2
251	toolchange_gcode =
252	top_infill_extrusion_width = 0
253	top_solid_infill_speed = 50
254	top_solid_layers = 3
255	travel_speed = 130
256	use_firmware_retraction = 0
257	use_relative_e_distances = 0
258	use_volumetric_e = 0
259	vibration_limit = 0
260	wipe = 0
261	xy_size_compensation = 0
262	z_offset = 0