challenge-bot.com Git - challenge-bot/blob - 3d-printables/makerfarm-i3-v-8in.ini

   1
   2 # [filament:makerfarm-i3-v-8in]
   3 bed_temperature = 70
   4 bridge_fan_speed = 100
   5 cooling = 1
   6 disable_fan_first_layers = 1
   7 extrusion_multiplier = 1
   8 fan_always_on = 1
   9 fan_below_layer_time = 60
  10 filament_diameter = 1.75
  11 first_layer_bed_temperature = 80
  12 first_layer_temperature = 235
  13 max_fan_speed = 100
  14 min_fan_speed = 35
  15 min_print_speed = 10
  16 slowdown_below_layer_time = 30
  17 temperature = 225
  18
  19 # [presets]
  20 # filament = makerfarm-i3-v-8in.ini
  21 # print = makerfarm-i3-v-8in.ini
  22 # printer = makerfarm-i3-v-8in.ini
  23
  24 # [print:makerfarm-i3-v-8in]
  25 avoid_crossing_perimeters = 1
  26 bottom_solid_layers = 3
  27 bridge_acceleration = 0
  28 bridge_flow_ratio = 1
  29 bridge_speed = 60
  30 brim_width = 0
  31 complete_objects = 0
  32 default_acceleration = 0
  33 dont_support_bridges = 1
  34 external_fill_pattern = rectilinear
  35 external_perimeter_extrusion_width = 0
  36 external_perimeter_speed = 70%
  37 external_perimeters_first = 0
  38 extra_perimeters = 1
  39 extruder_clearance_height = 20
  40 extruder_clearance_radius = 20
  41 extrusion_width = 0
  42 fill_angle = 45
  43 fill_density = 20%
  44 fill_pattern = 3dhoneycomb
  45 first_layer_acceleration = 0
  46 first_layer_extrusion_width = 200%
  47 first_layer_height = 0.35
  48 first_layer_speed = 30%
  49 gap_fill_speed = 20
  50 gcode_comments = 1
  51 infill_acceleration = 0
  52 infill_every_layers = 1
  53 infill_extruder = 1
  54 infill_extrusion_width = 0
  55 infill_first = 0
  56 infill_only_where_needed = 0
  57 infill_speed = 60
  58 interface_shells = 0
  59 layer_height = 0.2
  60 min_skirt_length = 0
  61 notes =
  62 only_retract_when_crossing_perimeters = 1
  63 ooze_prevention = 0
  64 output_filename_format = [input_filename_base].gcode
  65 overhangs = 1
  66 perimeter_acceleration = 0
  67 perimeter_extruder = 1
  68 perimeter_extrusion_width = 0
  69 perimeter_speed = 30
  70 perimeters = 3
  71 post_process =
  72 raft_layers = 0
  73 resolution = 0
  74 seam_position = aligned
  75 skirt_distance = 6
  76 skirt_height = 1
  77 skirts = 1
  78 small_perimeter_speed = 30
  79 solid_infill_below_area = 70
  80 solid_infill_every_layers = 0
  81 solid_infill_extruder = 1
  82 solid_infill_extrusion_width = 0
  83 solid_infill_speed = 60
  84 spiral_vase = 0
  85 standby_temperature_delta = -5
  86 support_material = 0
  87 support_material_angle = 0
  88 support_material_enforce_layers = 0
  89 support_material_extruder = 1
  90 support_material_extrusion_width = 0
  91 support_material_interface_extruder = 1
  92 support_material_interface_layers = 3
  93 support_material_interface_spacing = 0
  94 support_material_interface_speed = 100%
  95 support_material_pattern = pillars
  96 support_material_spacing = 2.5
  97 support_material_speed = 60
  98 support_material_threshold = 0
  99 thin_walls = 1
 100 threads = 2
 101 top_infill_extrusion_width = 0
 102 top_solid_infill_speed = 50
 103 top_solid_layers = 3
 104 travel_speed = 130
 105 xy_size_compensation = 0
 106
 107 # [printer:makerfarm-i3-v-8in]
 108 bed_shape = 0x0,200x0,200x200,0x200
 109 end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84     ; disable motors\n
 110 extruder_offset = 0x0
 111 gcode_flavor = reprap
 112 layer_gcode =
 113 nozzle_diameter = 0.4
 114 octoprint_apikey =
 115 octoprint_host =
 116 pressure_advance = 0
 117 retract_before_travel = 2
 118 retract_layer_change = 1
 119 retract_length = 1
 120 retract_length_toolchange = 10
 121 retract_lift = 0
 122 retract_restart_extra = 0
 123 retract_restart_extra_toolchange = 0
 124 retract_speed = 30
 125 start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n
 126 toolchange_gcode =
 127 use_firmware_retraction = 0
 128 use_relative_e_distances = 0
 129 use_volumetric_e = 0
 130 vibration_limit = 0
 131 wipe = 0
 132 z_offset = 0
 133
 134 # [settings]
 135 # autocenter = 1
 136 # mode = expert
 137
 138 # [simple]
 139 avoid_crossing_perimeters = 1
 140 bed_shape = 0x0,200x0,200x200,0x200
 141 bed_temperature = 70
 142 bottom_solid_layers = 3
 143 bridge_acceleration = 0
 144 bridge_fan_speed = 100
 145 bridge_flow_ratio = 1
 146 bridge_speed = 60
 147 brim_width = 0
 148 complete_objects = 0
 149 cooling = 1
 150 default_acceleration = 0
 151 disable_fan_first_layers = 1
 152 dont_support_bridges = 1
 153 duplicate_distance = 6
 154 end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84     ; disable motors\n
 155 external_fill_pattern = rectilinear
 156 external_perimeter_extrusion_width = 0
 157 external_perimeter_speed = 70%
 158 external_perimeters_first = 0
 159 extra_perimeters = 1
 160 extruder_clearance_height = 20
 161 extruder_clearance_radius = 20
 162 extruder_offset = 0x0
 163 extrusion_axis = E
 164 extrusion_multiplier = 1
 165 extrusion_width = 0
 166 fan_always_on = 0
 167 fan_below_layer_time = 60
 168 filament_diameter = 1.75
 169 fill_angle = 45
 170 fill_density = 20%
 171 fill_pattern = 3dhoneycomb
 172 first_layer_acceleration = 0
 173 first_layer_bed_temperature = 80
 174 first_layer_extrusion_width = 200%
 175 first_layer_height = 0.35
 176 first_layer_speed = 30%
 177 first_layer_temperature = 230
 178 gap_fill_speed = 20
 179 gcode_arcs = 0
 180 gcode_comments = 0
 181 gcode_flavor = reprap
 182 infill_acceleration = 0
 183 infill_every_layers = 10
 184 infill_extruder = 1
 185 infill_extrusion_width = 0
 186 infill_first = 0
 187 infill_only_where_needed = 0
 188 infill_speed = 60
 189 interface_shells = 0
 190 layer_gcode =
 191 layer_height = 0.3
 192 max_fan_speed = 100
 193 min_fan_speed = 35
 194 min_print_speed = 10
 195 min_skirt_length = 0
 196 notes =
 197 nozzle_diameter = 0.4
 198 octoprint_apikey =
 199 octoprint_host =
 200 only_retract_when_crossing_perimeters = 1
 201 ooze_prevention = 0
 202 output_filename_format = [input_filename_base].gcode
 203 overhangs = 1
 204 perimeter_acceleration = 0
 205 perimeter_extruder = 1
 206 perimeter_extrusion_width = 0
 207 perimeter_speed = 30
 208 perimeters = 3
 209 post_process =
 210 pressure_advance = 0
 211 raft_layers = 0
 212 resolution = 0
 213 retract_before_travel = 2
 214 retract_layer_change = 1
 215 retract_length = 1
 216 retract_length_toolchange = 10
 217 retract_lift = 0
 218 retract_restart_extra = 0
 219 retract_restart_extra_toolchange = 0
 220 retract_speed = 30
 221 seam_position = aligned
 222 skirt_distance = 6
 223 skirt_height = 1
 224 skirts = 1
 225 slowdown_below_layer_time = 30
 226 small_perimeter_speed = 30
 227 solid_infill_below_area = 70
 228 solid_infill_every_layers = 0
 229 solid_infill_extruder = 1
 230 solid_infill_extrusion_width = 0
 231 solid_infill_speed = 60
 232 spiral_vase = 0
 233 standby_temperature_delta = -5
 234 start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n
 235 support_material = 0
 236 support_material_angle = 0
 237 support_material_enforce_layers = 0
 238 support_material_extruder = 1
 239 support_material_extrusion_width = 0
 240 support_material_interface_extruder = 1
 241 support_material_interface_layers = 3
 242 support_material_interface_spacing = 0
 243 support_material_interface_speed = 100%
 244 support_material_pattern = pillars
 245 support_material_spacing = 2.5
 246 support_material_speed = 60
 247 support_material_threshold = 0
 248 temperature = 225
 249 thin_walls = 1
 250 threads = 2
 251 toolchange_gcode =
 252 top_infill_extrusion_width = 0
 253 top_solid_infill_speed = 50
 254 top_solid_layers = 3
 255 travel_speed = 130
 256 use_firmware_retraction = 0
 257 use_relative_e_distances = 0
 258 use_volumetric_e = 0
 259 vibration_limit = 0
 260 wipe = 0
 261 xy_size_compensation = 0
 262 z_offset = 0