clarify section title arduino to deck

[challenge-bot] / curriculum / challenge-bot.scm

;; tldr; AGPLv3+
;; copyright info at bottom

(document
 :title [challenge-bot]
 (chapter
  :title [mechanical]
  (section
   :title [arduino to deck]
   (subsection
    :title [arduino placement])
   (subsection
    :title [first hole]
    (subsubsection
     :title [choosing drill bit])
    (subsubsection
     :title [inserting drill bit])
    (subsubsection
     :title [holding drill])
    (subsubsection
     :title [drilling]))
   (subsection
    :title [first screw]
    (subsubsection
     :title [fastening arduino to deck using #6-32x3/8\" screw]
     (p [the "#6" part of "#6-32x3/8\"" is how big around the bolt is.
             it is related to wire gauge.
             bigger numbers mean larger screw.
             smaller numbers means smaller screws.])
     (p [check
         ,(itemize
           (item
            [in the motor assembly, there are #4-40x1.25\" screws.
                are those fatter, thinner, or the same thickness as the
                #6-32x3/8\" screws?]))])
     (p [the "32" part is a measurement of how close the threads are to
             each other.
             this is related to the angle of the thread, which is also
             called pitch.
             it is a count of how many times the thread wraps around one
             inch of the screw body.])
     (p [the head is the flat part where some tool, like the alan
             wrench, can exert force to spin the screw.])
     (p [check
         ,(itemize
           (item [how many times will the thread wrap around one inch of
                      the screw body?])
           (item [what about 2 inches?
                       how many times will the thread wrap around two
                       inches of the screw body?]))]))
    (subsubsection
     :title [fasten the arduino board to the deck]
     (p [push the 6-32 screw into the deck from the underside and at the
              same time, spin the 6-32 screw clockwise while looking
              down on its head.
              twist until the bottom of the screw is
              about to stick out on the top side of the deck.])
     (p [hold the arduino board flat to the deck and line up the arduino
              hole so the screw can come up through it.
              continue tightening the screw into the deck, spinning the same
              direction as before.
              tighten until the screw head touches the deck.
              do not continue tightening after that.])
     (p [the arduino should still be flat against the deck still, just
             as it was before tightening the screw.]))
    (subsubsection
     :title [assessment]
     (p [does the arduino stay with the deck when the deck moves?
              can the arduino board still rotate a few degrees?
              warning, if you rotate the arduino board too much, you
              will unscrew it from the deck and you'll have to screw it
              back in.
              rotating a few degrees should be ok.]))
    (subsubsection
     :title [arduino board move relative to deck]
     (p [without any screws, the arduino board can move independently of
                 the deck.])
     (p [with the first screw, the arduino can rotate around one point
              on the deck.])))
   (subsection
    :title [second hole and screw])
   (subsection
    :title [third and fourth hole and screw]))
  (section
   :title [breadboard])
  (section
   :title [battery packs]
   (subsection
    :title [leads])
   (subsection
    :title [deck attachment]))
  (section
   :title [motors]
   (subsection
    :title [leads])
   (subsection
    :title [mount])
   (subsection
    :title [deck attachment]))
  (section
   :title [wheels]
   (subsection
    :title [tread])
   (subsection
    :title [motor]))
  (section
   :title [caster]
   (subsection
    :title [deck placement]))
  (section
   :title [sonars]
   (subsection
    :title [deck placement])))
 (chapter
  :title [wiring and software]
  (section
   :title [serial]
   (subsection
    :title [software on computer]
    (subsubsection
     :title [arduino])
    (subsubsection
     :title [fritzing]))
   (subsection
    :title [attach arduino and computer via cable])
   (subsection
    :title [debugging common connection problems])
   (subsection
    :title [arduino reset button]))
  (section
   :title [left sonar]
   (subsection
    :title [breadboard connectivity])
   (subsection
    :title [cable])
   (subsection
    :title [arduino headers])
   (subsection
    :title [sound cm per microsecond at sea level]))
  (section
   :title [both sonars]
   (subsection
    :title [breadboard power rail]
    (p [power rail can provide power to more than one device.])))
  (section
   :title [left motor]
   (subsection
    :title [arduino digital output])
   (subsection
    :title [quad half h bridge, aka motor controller])
   (subsection
    :title [motor battery]))
  (section
   :title [both motors]
   (subsection
    :title [analogWrite]))
  (section
   :title [untethered]
   (subsection
    :title [arduino battery])
   (subsection
    :title [off and on functions]))
  (section
   :title [follow]
   (subsection
    :title [same wiring as untethered])
   (subsection
    :title [set motor])
   (subsection
    :title [go])
   (subsection
    :title [determining speed]))
  (section
   :title [stay on table]
   (subsection
    :title [stop])
   (subsection
    :title [backup])
   (subsection
    :title [turn around]))))

;; Copyright 2016 daniel watson

;; This file is part of challenge-bot.

;; challenge-bot is free software: you can redistribute it and/or modify
;; it under the terms of the GNU Affero General Public License as
;; published by the Free Software Foundation, either version 3 of the
;; License, or (at your option) any later version.

;; challenge-bot is distributed in the hope that it will be useful,
;; but WITHOUT ANY WARRANTY; without even the implied warranty of
;; MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
;; GNU Affero General Public License for more details.

;; You should have received a copy of the GNU Affero General Public
;; License along with challenge-bot.  If not, see
;; <http://www.gnu.org/licenses/>.